過濾式干燥處理機

◆成品優缺點 Product features

※極具保持穩定不同的撒氣負壓和露點

1.溶解塔之髙度與孔徑經科學實驗結果精密鑄造核算，塔床摩擦力小，保護了壓縮視頻實驗室氣體吹干劑5秒的使用時間間隔，需求產品氣的露點讓。

2.30％的干劑空間，應用于賠償標準干劑的物種多樣性銹蝕，保證干。

3.大傳播器，抓實氣浪粗糙能夠 干澡劑層，減少溝流后果。

※回收氣量自然損耗不大于14％

1.優勝的機筒設置，另存100％的活性炭吸附卡路里，儲存的卡路里用來上升重復時候的重復氣攝氏度，加快裝備的解吸性能，促使重復更充分。

2.烘干和再生利用能力主要采用反向的方式給回互流預案，濕熱空氣流經干的樹脂吸附劑限期果最好。再生利用能力氣出口處含濕量把握在亞趨于穩定形態，使改裝排氣管消音器器及改裝排氣管車道無返潮之慮。

3.可基于缺水機的電腦運行額(e)定負載業務需求調理二次利用利用氣攝入量，保持二次利用利用氣體連繼穩定性，二次利用利用壓低至臨界狀態。

※烘干劑應用平均耐用

1.剛好合適的機筒尺寸大小，使氣體用非常變干劑層的氣速和時間間隔要保持好的模式，充足發揮出非常變干劑的性。

2.科學的設計配置單，在熱空氣開啟機筒前，經除油凈化處理不能清掉熱空氣中內動植物油物與重被生態破壞的物，防范缺水劑層受被生態破壞的。

※專用設備主要采用了有新意高品格電動三輪及手動閥和靠譜的全微電子智能掌握序序掌握器，電腦工具欄合理，手動間斷性表示雙塔生產，再循環期直播可編，生產快速設置10min。調節閥生存期過去了50萬次姿態。

※壓力容器封頭內部作冷熱鍍防銹辦理辦理，10年不上銹。

※性動作更準、功效安全、運行簡單便捷，裝有不需根基。

※Bend it out on the same has the stable pressure and dew point

1. The height and diameter adsorption tower by the experimental results calculated precisely, tower, ensure the small resistance bed compressed gas desiccant 5 seconds contact time, meet the requirements of the finished product angry dew point.

2.30% of the surplus, desiccant used to compensate for the natural aging, ensure desiccant dry.

3. Large diffuser, ensure uniform through the desiccant air layer, eliminate channel flow phenomenon.

※Bend the gas loss less than 14% renewable

1. Excellent barrel design, save 100% of the adsorption quantity of heat, storage quantity of heat is used to increase the regeneration stage again angry temperature, improve equipment desorption ability, make renewable more thoroughly.

2. Dry and regeneration of the reverse convection scheme, wet air through the dry when the adsorbent best effect. Getting angry export moisture content control in the saturated state, the muffler and exhaust passage without concentrations of condensation.

3. According to the operation of the dryer load demand adjust dosage, ensure again angry for stability, regeneration renewable air pressure low to critical.

※Bend desiccant long service life

1. The right of barrel size, make the gas through the desiccant flow velocity and time of layer be the best, give full play to the desiccant performance.

2. The reasonable system configuration, in the air into the barrel, except by the efficient before oil processing timely removal in the air in content and heavy oil pollutant, avoid desiccant layer contamination.

※The equipment adopts bend novel high quality and pneumatic valve electric and advanced and reliable full electronic programmable controller, friendly interface, automatic continuous display of the twin towers, working cycle, the programmable factory set 10 min. The valve life for 500000 times action.

※Bend the cylinder body wall be cold galvanizing antirust processing, 10 years don't rust.

※Bend action, stable performance, accurate, easy operation and installation with no need of foundation.

◆通常科技參數指標 Main technical parameters